How to Use a Chainsaw Sharpener

Who wants a completely useless dull chainsaw, right?

If you operate the dull chainsaw, you know it’s a matter of pain. And realize the importance of a sharpen saw. A nicely sharpen saw will make your trimming experience accurate, fast and fun.

On the other hand, if you are a pro or have to cut the wood frequently, sharpen saw makes financial sense. 

How to use a chainsaw sharpener properly?

Well, it’s not Rocket science. Just follow the instruction given below and make it fun.

Techniques of Chainsaw Sharpener- Chainsaw Sharpening Tricks

So the first thing you should consider is actually when your chainsaw need to sharp?

Well, all you have to do is check out the waste material at the ground from your saw cut. If you see the dust that means it needs to sharp. And if it creates chips, it indicates the saw is sharp enough.

What will you need?

·         A chainsaw blade

·         A chainsaw sharpener

Now get back to work and try to follow step by step that shows the best way to sharpen a chainsaw.

Step 1: Setting the File

1.       First Clamp, the bar of the, saw to your work surface.

2.       Use the adjusting screw to balance and tighten the chain. Remember that the screw can be indifferent on the different saw. You have to figure out the right one.

3.       Mark your first tooth with the help of a permanent marker.

4.       Carefully select a round file according to the diameter as the chainsaw's teeth.

5.       Set the file in the notch on the front of the cutter.

6.       Try to Use a file holder to hold the file at the same angle.

Step 2: Sharpening the Cutters

To sharpen the cutter, slide the file across its face. Then told the file as it place flat or level on the top of the chain. You should file the cuter 4 to 10 times it is sharp enough. Now sharpen every second tooth just from the starting point.

What about chainsaw sharpening angles?

 Rotate the saw 180 degrees. Try to use the same motion and chainsaw sharpening tools.

Step 3: Filing the Rakers

Put a depth gauge over the saw’s chain. Be careful if any part of the raker remains the top of the depth gauge. Apply a flat mill bastard file for level up the raker. Ensure that form that you file every other raker at the same height. Then loosen the chain as well as release the chainsaw. Refill the oil reservoir in your chainsaw.

Chainsaw Sharpening Tips

·         Always wear protective gloves when sharpening a chainsaw or cutting attachment.

·         Remember Chainsaw teeth are quite sharp and will cause injury.

·         Read the user manual and instruction properly before sharpening the saw. Meanwhile, the different brand sharpener is quite different.  Electric chainsaw sharpener is not same as Stihl chainsaw sharpener.  So follow the instruction.

·         Don’t pull the file backward, as this can damage both the cutter and your file itself.

Untangle Saw Trick 101: How to Untangle a Chainsaw Chain

picture from:https://sumogardener.com/ 

Can’t get loops out of a saw chain?

Don’t worry; you are not alone. All the guys out there who are an owner of a chainsaw can realize it. The good news is you come to the right place. Today, I am going to show you the easiest way to untangle the chain. So that after the end of this how to untangle a chainsaw chain, you have a clear on the basic of untangling saw. Stay along.

Preparation before Starting

Untangling the chain can be very boring if you don’t know the appropriate process. Things you need to prepare to continue the process are

• A Sturdy Table or surface
• Chainsaw Gloves
• Tools
• Lubricating Oil
• Protective Goggles

Untangling the Saw Chain

As we mentioned earlier, keeping yourself safe first. So wear the protective gloves and goggles before the start. Now follow the instruction step by step.

Step 1: Make the Necessary Preparations

Place the saw on a flat table or the workbench. If the chain has been removed from its bar, you have to use the right tools so you can remove the housing, the chain, and the bar.

But if your chain is new, find out its sharp edge to ensure that it won’t cut you. Be careful about the old one who can stick or rusted together, then loosen it with enough lubricating oil. And try to avoid scattering the oil on the floor to avoid accidents.

Step 2: Figure out the Two opposite Loops

After taking a good preparation, now you have to find out the two opposite loops in the chain. Place each of the hands on the loop to allow it to hang down using these two points. Meanwhile, it will help to unravel the chain by lessening the complexity of the tangle.

Step 3: Making both Loops Bigger

In this stage, you can assume the full extent of the tangle. Now try to find out the possible way to make those loops bigger till it is good enough to make it in one single loop. Ensure that your hands are in the two most opposite loops. You can use a slack on the chain.

Step 4: Untangling the Chain

                                                   picture from: https://sumogardener.com/ 

Your hands are still in that place, right? Great, then located at the lowest part of the saw’s chain. Now guide and allow shooting straight up. Remember that chains are quite stiff. To apply the correct techniques to raise the loops easily.

Also, it will allow the gravity to let that raised portion smoothly. Meanwhile, if there is any tangle still, you must make two loops to repeat the same process.

Step 5: Spreading Them Apart

If three steps of above did not work very well at all for you, then this part is for you. Try to untangle by focusing on each tangle or loop. Also, spread each of them as possible. This is to make it less complicated. chainsaw sharpener is another important topic for chainsaw lover.

Tip

·         New chains are quite clean and well-oiled. But when you are working with an old chain, clean off all the debris. Also, spray a bit of lubricating oil to help it slide more easily to untangle. 

Echo Chainsaw Review | The Ultimate Choice of the Professional

Want a smooth cutting with less effort?

If yes, then you have come to the right place. Today in this article, you gonna get Echo chainsaw review that may help you in your next buy.

You may be a bit surprised to see that many people choose to buy Echo chainsaw, even they are relatively expensive. The reason behind this is they worth your penny. Most importantly, Echo chainsaw gives superior performance. Let’s dig into deep to know much about these amazing saws.

So let’s get started.

Who makes echo chainsaws?

The Echo brand is manufactured by the renown Yamabiko Corporation situated in Ome, Japan.

Yamabiko have been started to produce this type of saw around since 1947. Hence, the first professional saw was manufactured under the brand in 1978 at Echo Incorporated, Northbrook, IL.

Design

Just By a single look, you will realize, Echo chainsaw is very solidly made. Thus, the balance is perfect. The thing we like most about this product is the steel cut-off switch. This feature makes it reliable and simple.

Like all ECHO equipment and tools, Echo chainsaws are designed with professional-grade material to ensure the highest value from your investment. Meanwhile, there is a vast range of complementary tools and Parts available for the chainsaw.

Functionality and Performance

An ECHO Chainsaw is designed to tackle your toughest jobs. Whether you're cutting firewood, pruning limbs, or taking down a tree, each Echo Saw is built to provide trouble-free life. So you want a saw that starts easy and provides years of reliable performance, then ECHO Chainsaw is best.

ECHO's superior quality starts with a high performance, a Pro-Fire® ignition system, and 2-stroke engine that ensure smooth operation as well as fast starts.

Warranty

Yeah, when you purchase a power tool, there is a decent investment behind it. So it’s pretty obvious that you want to make sure the brand standing behind their products. So don’t afraid. ECHO never consider about quality. Besides, they gave a 2-year commercial warranty for their product. But keep in mind that the warranty might be void if there is any misuse.

What we like most about Echo chainsaw?

1. Lightweight as well as nimble
2. Compact, well-balanced design
3. Outstanding performance
4. Fully Assembled
5. Automatic, adjustable chain oiler

What could be better?

• ·         Some models are a bit heavy.

Some Best Echo Chainsaw

1. Echo 30.5CC Chain Gas Saw – Best for the homeowner

If you are a small property homeowner, then this one is ideal for you. Meanwhile, this 14-inch bar comes with some great features like Anti Vibration Handle and 2 Stroke Oil.

2. Echo 26.9CC Chain Saw-Best for Professional Use

 Link: https://www.amazon.com/Chain-Saw-Gas-Bar-26-9CC/dp/B005UDT4HM?tag=chaingeek-20

The Echo Chain Saw is an 11 oz trimming beauty, which can be a trustworthy trimmer for professional. With 12 inch bar, this is originated from Japan.

3. Echo CS-400 Gas Chainsaw- Best for Beginner

Link: https://www.amazon.com/Echo-CS-400-18-Gas-Chainsaw/dp/B0016RRNAG?tag=chaingeek-20

Echo CS-400 comes with Genuine OEM Echo Part. One definite advantage of this saw is the i-30 starting system which ensures reduced effort starting. However, it is Fully Assembled and includes Engine Oil.